Monday, May 23, 2011

Bitcoin mining rig is up!

Picture of my liquid-cooled box of 4 Radeon HD5870 cards, before closing up the case and actually getting it to work. It computes about 1.3 Gigahashes per second. (Click to enlarge.)



The side panel that closes it off (not shown) adds another large fan, which I inverted so it's sucking the hot radiator exhaust air out.

UPDATE 5/24/11: I've switched to the Phoenix miner, which somehow gets more hashes out of your card, so I'm now computing about 1.5 Ghash/sec.

127 comments:

Burt Wagner said...

With todays network number of 3.579 Thashes/s (http://bitcoincharts.com/bitcoin/) and your published number of 1.3 Ghashes/s your rig should represent about 0.0363% of the network. At 50 BTC/block and about $7 per BTC this works out to about $18.30 per day. Is this correct? I ask because I am considering buying a rig myself.

Silas Barta said...

Thanks for the comment, Burt.

First thing: over the initial 24 hours that I was running this rig, pooling with deepbit.net (which takes a 3% cut), I got ~5.5 BTC, or $38.50. The parts for the rig cost me ~$2800 (although I've only now started to run it at full capacity -- previously I could only run two of those cards, earning about $650 at low capacity).

The network capacity of 3.6 Thash/s doesn't sound right. One way to calculate network capacity is to find some big computer on it and find its hashrate, then multiply that by the ratio of its average block-finding time.

For deepbit.net, it does 1.1 Thash/sec and solves a block every 15.5 min on average, whic means it has about 2/3 of the network -- but that's just a rough estimate, I guess.

Anywayhe key parts for this system are:

4x Radeon HD 5870 GPU
4x VID-AR587T2 GPU waterblock
1x Coolermaster HAF X Chassis
1x Antec HCP-1200 ATX PSU
1x MSI 890FXA-GD70 Motherboard
1x Swiftech H20-320 EDGE liquid cooling kit (comes with tubing, 4 barbs, and clamps)
1x 1/2 inch elbow barb to make that connection at the bottom work
ALOTx your elbow grease

Then just add a cheap solid-state HD and CPU.

I'll leave it up to you to decide if it's worth the expense and risk.

Burt Wagner said...

Check out the latest numbers:

Network: 6.996 Thashs/s !!

Current difficulty: 434,883

Next difficulty in 2010 blocks: 1,102,949 !!

Also the largest growth was in the "other" category (not any one coop). In fact deepbit is now less than 25% and could be as low a 20%!

Sources: http://bitcoincharts.com/markets/ and http://bitcoinwatch.com/

Wild, check out this chart: http://bitcoin.sipa.be/speed-lin-10k.png

Silas Barta said...

Neat, thanks for the info!

Burt Wagner said...

I must appologize for my previous post. It turns out that right after a rise in difficulty all of the estimates for the next difficulty, the total network hash rate, the distribution of productivity, etc. are just wrong. It turns out you have to wait about 24 hours for all the averaging mechanisms to calm down before you get accurate numbers. So if you recheck the URLs I gave you in my previous post you will find that things have calmed down at the numbers are not as dire as I thought.

Hans said...

Could you just use the standard fan-cooled HD 5870s? Or wouldnt they fit onto the mainboard? Or get too hot?

Thanks

Silas Barta said...

They get way too hot with just aircooling, which is why I set up liquid cooling. I could only have two running with aircooling, and the hottest one would get close to 90 C (without overclocking), which is really pushing it. With the liquid cooling system I have, I can run all four GPUs overclocked and the hottest one gets to 60-70 C.

So, I learned not to do aircooling for 4 5870s the hard way...

Anonymous said...

@Silas - why do the graphic cards look different than original 5870's?

Like this one:
http://hothardware.com/articleimages/Item1383/AMD-ATI-Radeon-HD-5870-Card.jpg

Silas Barta said...

@Anonymous: Most of what (by mass) makes up a graphics card (as it is out-of-the-box) is the heat sink attached to it. In the picture you linked, that includes the red circle thing and the blank casing.

To switch to water-cooling, you have to remove this OEM heat sink and attach your own waterblock, the latter of which which is much smaller and doesn't cover the full circuit board. And that's what I did here in the setup.

In the process of making this, I took a bunch of pictures, some of which show a modded card next to an out-of-the-box one, and I may upload those sometime.

Hope that makes sense.

Anonymous said...

Hey thanks for all the info. So how many coins are you mining in a 24hr period currently? Great looking rig.

Silas Barta said...

I'm going to remain a bit coy about that number so people don't know whose wallet file to go after ... ;-)

Anonymous said...

Fair enough. Okay, but you are saying, it is clearly worth the investment for you?

Silas Barta said...

At this point, it's definitely worth the investment. If I sold all my bitcoins (even after the recent fall to 24), it would more than cover the cost of my equipment, plus my labor at my current wage rate (in my day job), plus a decent profit -- and it's still generating.

I always feared that the difficulty would go up and slow down my coin generation rate. And it did. But the gain in value of bitcoins has more than compensated for this, so, in dollar terms, the daily yield has been pretty constant.

Kevin Carnage said...

Hey man, I'm about to order some components for my own rig, and am in love with the 4 card mo-bo with liquid cooling. :) I was wondering if an 850 watt power supply will be enough tp power 4 5850's or if the 1200 is really what I need?

Silas Barta said...

Hi Kevin. First, I'm not sure how profitable it's going to be now; at 1.6 GHash/sec, I'm only getting ~1 BTC/day. (It would have gotten ~25/day if I had that much computing power when I was planning this...) You'll have to bank on further runups in BTC value.

As for the PSU question, I would be hesitant about using that much. That card uses ~188 Watts, which leaves only about 100 W for the hard drive, CPU, and cooling system. The overclocking forums should be more helpful.

Kevin Carnage said...

Thanks for the quick reply. :) Is the reason its less profitable because of the increased difficulty in breaking blocks?

Also, I ran the numbers and found that at the current difficulty, with a $2500 investment, it would pay itself off in about 5 months, which if it continued at a stead rate, would be an almost 55% annual return on investment, which is better than any other investment I could throw capital into right now.

Where do you think the value of bitcoins is going? If they go back up to $30 a coin, it would pay itself off in about half the time.

Silas Barta said...

@Kevin, yes, I was basing my estimate on the increasing difficulty factor. But you're right, I'm also holding this to a higher standard than other investments. Still, there's a lot of risk involved. If a 55% yearly ROR is sufficient for you on this kind of thing, go for it. Just keep in mind that the revenues will be anything but steady.

As for the price, Bitcoin is still in its nascent stage, with big swings either way. I remember back in April, my friends and I did think it was worth it to buy at $1/BTC! Fortunately, the daily value produced has been steady: for a while, the increase in difficult factor was matched by the increase in BTC price.

Silas Barta said...

Sorry, that should say my friends and I didn't think it was worth it to buy at $1.

Kevin Carnage said...

Thanks again Silas for your timely response and good information. Your absolutely right in that there's a risk in virtually any investment. That being said, it seems as if the only way it would be a bad idea is if the cost of equipment, maintenance, and electricity ever exceeded the value of bitcoins recieved from said hardware.

If it ever became unprofitable to mine, do you believe that would that cause the whole system to collapse?

Silas Barta said...

@Kevin: Glad to help!

That being said, it seems as if the only way it would be a bad idea is if the cost of equipment, maintenance, and electricity ever exceeded the value of bitcoins recieved from said hardware.

Yes, but those are big "ifs". Just be aware of the risk of a) sigificant decline in Bitcoin value, or b) significant increase in difficutly factor not offset (as it was for a while) by an increase in Bitcoin value.

If it ever became unprofitable to mine, do you believe that would that cause the whole system to collapse?

The way the protocol is designed, it can't become unprofitable for _everyone_ to mine. The difficutly factor is adjusted so that coins are created at a predictable rate, and if a large number of miners ever leave the system, the difficutly will adjust downward until a new equilibrium level of mining is reached. This is done automatically, in a way not requiring anyone's judgment or permitting arbitrary decisions.

I explain the details of it in an as-of-yet unappreciated comment on Bob's blog.

Kevin Carnage said...

Wow, that is certainly amazing, and at the same time incredibly complicated. Yesterday I learned about the recent spike and crash in bitcoins more fully, opening my eyes to the instability of the market. What do you plan to do with your bitcoins? Hold them or sell them off to avoid losing everything?

I also learned that Mt. Gox was hacked and they acquired everyone's username and password, which is incredibly troubling. What's to stop those hackers from doing it again?

And i'm terribly sorry if I'm wasting your time with these questions but I have one more big one me and my friend though of last night, what happens when there's no more bitcoins to mine?

Silas Barta said...

Keep in mind, the crash to ~$0 was local to one exchange and due to a hacker. The price on other exchanges at the time was unaffected.

And in any case, the exchange Mt. Gox, is just one of many users of Bitcoin, as I tried to make clear in a more recent post, so you have to be careful not to equate the two, but at the same time, do be careful about which exchange you use. And, all things considered, Mt. Gox handled it well, locking it down and minimizing the damage.

Hopefully, they've learned from the attack and have sealed the holes (in this case, it was an auditor being careless with the access they were granted). If their handling of future breaches is any better, it doesn't seem like anything to worry about: the withdrawl limits allow them to quickly contain any damage, as they did on this one.

As for what I'm doing with my BTC, mainly holding on, since I think its network effects have yet to be fully appreciated and priced in.

Silas Barta said...

I have one more big one me and my friend though of last night, what happens when there's no more bitcoins to mine?

Keep in mind, miners who solve a block don't just get the 50 BTC (or whatever); they also get any transaction fees offered by users, which are optional but increase the speed with which your exchange is incorporated into the database.

So when the scheduled "minting" of new bitcoins ends, miners will still get to keep these transaction fees, which, by that point, will probably have already exceeded the diminishing block reward (remember, it halves every few years so near the end of the minting phase, it will be below 1 BTC/block).

Kevin Carnage said...

You certainly seem to be incredibly informed and insightful about how this whole thing works, it's incredibly complicated to say the least. I'll let you know how it goes for us, your advice has been indispensable thus far :)

Kevin Carnage said...

Is there any particular reason you went with the 5870's instead of the 5830's? I looked a lot into pricing on the two cards and decided to go with the 5830's because I guess they get about 319mh/s and cost about $137 a piece, making them 2.33mh/s/$ the lowest I could find the 5870's for was $275, running at 445mh/s they only come out to 1.618mh/s/$. However, I did find it interesting that last figure came out to be the golden mean somehow :) (1.618)

Silas Barta said...

Glad I can help.

Interesting stuff on the calcualtions. The reason I went with 5870s was based on what the hardware comparison page on the bitcoin wiki showed circa February of this year. I wanted a high absolute hashing rate, but also high ROR. The highest total hashing rates came from 5970s and 5870s; the latter were half the price and more than half as fast. Also, 5970s were rapidly becoming scarce, and indeed the hordes of miners buying them led to the first ever price *increase* of a mining card that I've seen, so the comparison became even more favorable toward the 5870.

I didn't look at the others you mention very closely, probably because they weren't on the list at that time.

Kevin Carnage said...

Hello again, just noticing that bitcoin prices were in freefall, penny for your thoughts on the matter?

Silas Barta said...

I noticed the same thing, but figured it would be temporary. ANd not it looks like it's pulled back up around $15.

Anonymousg64 said...

How do you manage power consumption, max on a wall outlet is 1440W, what should i do if i where to get a 4000W mining Rig?

Silas Barta said...

Get a separate room or warehouse for it. No joke: if you're going to go that far, you need to anyway. There are videos ong youtube of people doing just that.

Kevin Carnage said...

Hey man, for thee water cooling, could you kindly direct me to website where you ordered that 1x 1/2 inch elbow barb? Was it Koolance.com?

Silas Barta said...

Hey, sorry I haven't followed up in the comments. I got the elbow barb here.

Kevin Carnage said...

Okay cool,Do the barbs that come in the swiftech kit function as nozzels for the waterblocks on your graphics cards?
Also I maybe have ordered the wrong thing, this is what I ordered for the elbow joint. https://www.koolance.com/water-cooling/product_info.php?product_id=562
I can simply cancel and reorder the correct one if that is the case.

Thanks a lot, again, your help has been critical.

-Kevin Carnage

Silas Barta said...

The barbs that come with the swiftech kit have one male end that screws into the threaded holes on the waterblock (or radiator), and one end that you attach the tubing to (the latter of which is what makes it a barb).

The part you linked to is just an elbow, which screws into something (the radiator or waterblock) on one side, and has something (a barb) screwed into it on the other side. For that part to connect to a tube, you would have to screw a barb into the female end.

The part I linked to is a combined elbow/barb so that you don't have to do the last step of screwing a barb into the elbow -- it's already built-in.

The swiftech kit comes with 4 barbs, two of which are intended for a free CPU waterblock that comes with the kit, but works for the GPU waterblocks just the same. If you, like me, won't be putting a waterblock on your CPU, you can just salvage them for your radiator/waterblock connections, so you'll have all you need.

Since you have four barbs in the kit, the elbow you linked is all you need, since you can screw one of them into the elbow. The only reason I got a combined elbow/barb is to be extra safe and avoid having one extra connection (between the elbow and its barb).

Does that make sense?

Silas Barta said...

Btw, something's screwy about that link you gave: the picture on the right doesn't seem to be a representation of the product. If you look at "more pics", you only see the left picture -- and the same thing happens if you click the right picture!

Kevin Carnage said...

Things are definitely starting to come into focus more and more. Your explanation about the water cooling system was incredibly helpful. To avoid ordering another part, and canceling the previous order, I'll just try screwing the barb into the elbow and the elbow into the waterblock? That should work right?

Also Your right, the pictures on that page are messed up. That is a little bit weird, someone messed up.. lol

Silas Barta said...

Yes, that elbow you linked will work. It has a male end that screws into the GPU block, and a female end that the barb screws into.

One thing I forgot to include in the parts list: connectors for between the blocks. Basically, to avoid having to run extra tubing between each block, you can get special connectors that directly connect one block to another. (As a bonus, they stiffen the overall structure, and keep the cards from bending down due to the weight of the waterblocks.)

You will need one for each connection between blocks. Since my cards were as close together as the motherboard allowed (1-slot spacing), I used these. (In my case, with four cards, I needed three of them.)

If there's more space between your cards, you would need to get a 2- or 3-slot connector.

Btw, setting up the hardware is only half the battle ... there's also the software, but you can find lots of tutorials on the bitcoin forums.

Kevin Carnage said...

Awesome man, and these connectors will work for pretty much any waterblock? these in particular..

http://www.koolance.com/water-cooling/product_info.php?product_id=2021

You seem to have all the answers man, I can't imagine how long it took to figure all this out for yourself. As for the software, lol, It it pretty crazy, we're just crossing that bridge when we come to it for now..

Silas Barta said...

Yikes, you're going for the big leagues, aren't you?

In any case, most liquid cooling connections use "G 1/4 BSP" (British Standard Piping, not compatible with what you can get a local US stores), and the part you linked is no exception, so it will work.

It was definitely a learning experience for me getting it to work, I'm glad I can pass on what I learned.

Kevin Carnage said...

Hello again,

How's your mining operation going? What kind of results are you getting now with the increasing difficulty?

I have run into a slight problem, it seems the Koolance VID-AR697 waterblocks I ordered do not fit the XFX Radeon 6950 graphics cards quite right. In the instructions provided it looks as if the pieces on the card that are in the way had been removed from the card in the photo but I don't want to just start pulling pieces off the board.

Or, is there anywhere else that might sell waterblocks specifically for the XFX Radeon 6950's?

Silas Barta said...

Sorry to hear about that. I had the same problem when I was putting my machine together -- the first waterblocks I bought didn't fit the card so I had to return them and buy a more expensive kind. I hope you only opened one.

I forgot to add that you should check with the site if they think the block will be compatible with your specific card. Usually, that means take off the heatsink any any easily removable parts, leaving the printed circuit board (PCB), take a picture of that, and send it to the site to verify that a given waterblock will worth with your card.

Also, check the site's forums or overclocking forums for what specific waterblocks work with that card.

As for my progress, I haven't actually been running it very much recently for various reasons (mainly because of summer cooling costs).

Kevin Carnage said...

Okay thanks again man, good luck trying to beat the heat.

Kevin Carnage said...

Hello again, hope you have been doing well. Upon running into uncertainty about the watercooling kit I got from swiftech, I posted on Tom's Hardware asking for advice and was recommended that I get more radiators for the cooling system. How were you able to get by with only one radiator? Or do you actually have more than one radiator and it's not apparent in the picture?

Silas Barta said...

Hey, sorry, only just saw your comment (need to set up something so I get notices). The one I got was sufficient for me (it's the one with three fans), but you may have to adjust a few things to get it right. Make a note of which direction each fan points.

For example, in my setup, the radiator fans draw ambient air from above the rig, and push the (warmed) air _into_ the case, which is, of course, less than ideal -- because the hot air near the GPUs makes it a little harder to reject heat (but not of course a deal-breaker because the liquid sucks out heat much faster than the surrounding air).

To make up for this, I have the case side fan (not shown) flipped around so that it brings more ambient air into he box. The rear fan is then hard at work sucking out all the box heat.

There are alternate ways to do this of course: you could flip the radiator around so that it uses the hot case air to cool down the fluid in the radiator and thus cool down the inside (I would have done this but it would have bade the tubing more complicated). Or, you can use the optional mounting kit to suspend the radiator vertically just a few inches behind the case so that it both draws air from, and expels air to, a region not inside the case.

What exactly is going wrong? Is the system working but cooling the GPUs as much as you wanted? Mine go up to ~75 C sometimes even with the liquid cooling.

Kevin Carnage said...

Everything else is good to go, I was only worried about whether the extra rad would be needed because of the comments I got from the people on Tom's. I'm probably getting another 3x120mm fan rad in order to keep these puppies nice and cool. They are beast, and if I plan to get maximum performance out of them I want to do this right. May have to mount the extra rad on the outside like your said but I think it'll work. I'll let you know how it goes when everything is in order. Thanks again.

Silas Barta said...

Glad to hear it's going well. Can you post a link to the thread in Tom's Hardware?

Kevin Carnage said...

Yeah man, no problem, check it out. http://www.tomshardware.com/forum/268631-29-water-cooling-radeon-6950#t1928318

Silas Barta said...

Interesting, I probably should have mentioned that I did some (well, many) leakage tests (albeit crude ones) before running it. For example, once I had the fittings connect all the cards in series, I put pieces of tubing at the end, and sent water through, and also blew into the pipes to increase the pressure. After everything checked out, I got it running, but even so it leaked a bit -- not enough to be sustained or caused problems though.

Anonymous said...

Justread this post. Lots of interesting information. Selling my restored boat in a few days for a little over $40,000 USD. I inherited it and hate boats ;)

Really want to throw the money at a bitcoin mining setup.

What are your thoughts on this? Hardware tips, setup tips, profit estimates?

I am pcproficient, but a bitcoin newb.

Kevin Carnage said...

$40,000 worth of mining equipment? :0' ' ' *drools... If your about to go that route, you have two basic options:

1) Set up some racks in room that you have dedicated to the rigs, air condition the room, and have plenty of fans to circulate the air, Something like this: http://www.youtube.com/watch?v=eLt8Se3vVNg

2) Open-air rigs with your GPUs on raised rails.. with this option you have to be more attentive about things like dust, liquids, and other dangerous foreign objects: they talk more about it here: http://www.overclock.net/intel-general/1023779-when-running-rig-open-air-when.html

http://www.youtube.com/watch?v=lEGIZOO-HYY


Keep in mind this quite a large undertaking you are about to embark on. I myself am somewhat of a noob to bitcoin as well but I believe strongly in the idea of a P2P currency, and the potential bitcoin has to change the world. That being said, there is a great possibility of failure associated with the incredibly high rewards if bitcoin does succeed, and you should always weigh these options for yourself before doing anything.

Good luck with whatever you decide, post some pictures and/or videos if you do get something together :) Very interested in what comes out of this one.

Free Bitcoins said...

Computer setup like this would be a present day, super high end valued rig. If you have a good basis and cooling, video cards and power supplies would be the least of your troubles financially.

Free the Bitcoins said...

Sorry forgot to leave link... hah
http://www.youtube.com/watch?v=CTv2hEfeFP4

runeks said...

That is like my *dream* Bitcoin mining rig. Except replace the 5870's with 5970's :D.
Four 5970s would consume 1200W in total though (without any overclocking). So the rig would probably need multiple power supplies (to avoid the cost of buying a single big one) which wouldn't fit in the case, and would kind of ruin the aesthetics of it. But very nice looking rig! Water cooling rocks.

Anonymous said...

Have you thought of undervolting the cards yet? It seems that power consumption is a square of the voltage. I've heard the best way to do this is to underclock the cards down to like 500 mhz, then keep dropping the voltage till something stops working. Jump back up to the previous stable setting, then incrementally increase the mhz again until things break. This way you get the lowest possible voltage running at its highest possible speed.

Also, now that it's winter the power/cooling cost aren't as wasteful (turned my 3x5830 miner back on).

I'd like to install water blocks so I can run the radiator outside. Heat will be overwhelming here in Florida in a month or two.

Kevin Carnage said...

Hello again,

I'd like to post of picture of a rig I built with help from this blog. Can I sent it to your email Silas and you post it at the bottom, it's not quite as pretty as yours but it is pretty righteous.

-Kevin

Unknown said...

I'm assuming it undergo to several rigging inspection to be able to make it safer to everyone especially to those who will be using this one. And yes, rigging has become important nowadays to hold up and put things together.

Unknown said...

A system unit like this one doesn't have to have a 5th axis rotary table. But I still wonder how a system unit like this one would look like if if has an installation of a rotary table.

Trinityserviceshvac said...

Power supplies would be the least of your troubles financially.
AC Service New Orleans

Alex Smith said...

There are alternate ways to do this of course: you could flip the radiator around so that it uses the hot case air to cool.
AC Service Kenosha

Unknown said...

Keep in mind this quite a large undertaking you are about to embark on. I myself am somewhat of a noob to bitcoin as well but I believe strongly in the idea of a P2P currency.
Air Conditioning Service Spring Branch

Kowalski Brothers said...

it's not quite as pretty as yours but it is pretty righteous. thanks for the post.

regards
Roof Repair Cockeysville MD

bellaireair said...

It doesn't seem like anything to worry about: the withdrawl limits allow them to quickly contain any damage, as they did on this one.
Attic Insulation 77096

Heating 77079 said...

The rear fan is then hard at work sucking out all the box heat.
Heating West University

simplycozy said...

This way you get the lowest possible voltage running at its highest possible speed.
AC Service Friendswood

Unknown said...

Your blog is so beautiful and natural all are like your blog everyone appreciate your blog. Whenever We will see your blog every time we get something new about your blog This is the very informative content. I am very appreciate to your site who provide us this informative resource thank for sharing us this information.
delltruck

bitcoin said...

Nice hardware but are you still using this old rig or have you upgraded to an ASIC yet?

Unknown said...

There are alternate ways to do this of course: you could flip the radiator around so that it uses the hot case air to cool down the fluid in the radiator and thus cool down the inside (I would have done this but it would have bade the tubing more complicated).
AC Repair Frisco

sunglowinc said...

I still wonder how a system unit like this one would look like if if has an installation of a rotary table.
Heating Clackamas

bellaireair said...

The only reason I got a combined elbow/barb is to be extra safe and avoid having one extra connection (between the elbow and its barb).
A Service River Oaks

ferrugiamechanical said...

Power supplies would be the least of your troubles financially.
Ac Service Montgomery

Unknown said...

I have been to your blog before. The more I visit, the more I keep coming back! ;-)
air conditioner installation in toronto

Air conditioning Service said...

I learned about the recent spike and crash in bitcoins more fully, opening my eyes to the instability of the market.
Air conditioning contractors Bellaire , TX

Peter Griffin said...

Now that's a decent set-up of your computer! I bet that playing your favorite game in that console will truly be awesome!

Unknown said...

The only reason I got a combined elbow/barb is to be extra safe and avoid having one extra connection.
AC Repair Pearland

Anonymous said...

Thank you for another essential article. Where else could anyone get that kind of information in such a complete way of writing? I have a presentation incoming week, and I am on the lookout for such information. hvac repair denver

Unknown said...

Hello dear guys,

The area and neighborhood is the most important thing to consider when building a laundromat business.The best laundromats in Toronto are as hard to find as a missing sock. There are thousands of them in the city, and most are destined to ruin your clothes sooner or later (probably sooner). But laundromats force us into the uneasy choice of convenience over quality, so we take our chances with unreliable washers and unclean dryers simply because we can walk over to the place in our pyjamas.Read more at-:24 hour Toronto coin laundromat


Thanks and welcome
Jassica Rose

Unknown said...

Hello dear guys,

The area and neighborhood is the most important thing to consider when building a laundromat business.The best laundromats in Toronto are as hard to find as a missing sock. There are thousands of them in the city, and most are destined to ruin your clothes sooner or later (probably sooner). But laundromats force us into the uneasy choice of convenience over quality, so we take our chances with unreliable washers and unclean dryers simply because we can walk over to the place in our pyjamas.Read more at-:24 hour Toronto coin laundromat


Thanks and welcome
Jassica Rose

Anonymous said...

Hi there,

While this is happening, these same individuals pull out their spring and summer clothing from storage. Since all of this clothing has been in storage during fall and winter they will also add to the washing and drying load. As you can see, all of this adds up to a really good month for the coin laundry business.Read more at-Coin laundromats in Toronto


Thanks and welcome
Alexander Ariana


Unknown said...

Hello dear friend
A major advantage is that a Laundromat has the capacity of taking a huge load of garments.By this means, it saves lots of time and energy.Read more at- laundromat Toronto

Unknown said...

Hello everybody
For building a coin-operated laundromat facility or how to buy a laundromat, you will need to know a few things. Building a coin-operated laundromat is something everyone should consider. You can purchase a laundromat without having to worry about all the employees, details, maintenance costs, etc..See more at- 24 hour Toronto coin laundromat

Unknown said...

Hi....When you are down and in trouble, keep fighting. Don't give up. keep kicking. It won't help to wallow in self-pity, or curse your stars or play the blame game. Every adversity has an opportunity couched within. It is up to us to grab it. And what you do when the going gets tough, is what defines your outcomes.Read more-Depression Help Services Florida

Unknown said...



Hello.....There are many things that make Florida unique, from its history to its geography to its culture. When it comes to recovery from addiction, Florida drug rehab centers are especially unique. They employ a model of treatment called the "Florida Model", which has revolutionized the practice and approach to addiction treatment. This is the primary reason why so many addicts choose Florida as their recovery destination.See more-Depression Help Services Florida

Unknown said...

Depression is a world, depression leaves you lost, depression drops you into a never ending blackhole, you want to get help, but you can't, when you do you wish you didn't, depression leaves you numb with fear, depression leaves you no hope, no ambition, nothing to look foward to, tears well in your eyes, depression leaks out into the open.Read more:-Depression Help Services Florida

Unknown said...

As a laundromat business owner, how do you optimize your laundromat to get the most out of every dollar you have invested in your laundry business? Read this article to find out how to increase your cash flow as well as net worth by optimizing the performance of your laundromat business.see more at:-coin laundromats in Toronto

Unknown said...

Hey
I would like to share a news Though running a Laundromat is can be a great business venture, there's more to it than meets the eye. Aspects such as location, equipment and services offered will go a long way in ensuring its success. See more at-Laundromat Toronto

Unknown said...

Hey guys
There is a lot to be considered when it comes to locating a coin operated laundromat business or buying an existing operation. One of the main concerns is the location. The right location will help you to get the volume of customers that you need to sustain your business.see more at:-laundromat Toronto

Anonymous said...

Great post. This article is really very interesting and enjoyable. I think its must be helpful and informative for us. Thanks for sharing your nice post. denver furnace repair

Unknown said...

Hi there,
I'm going to let you in on a few insider secrets that determine the value of a coin laundromat business. These few tips can dramatically increase the your wealth and income.See more at- Laundromat 24 hours Toronto

Mike said...

We just couldnt leave your site before saying that I genuinely enjoyed the quality information you provide to your visitors? Will be again soon to check up on new posts. Please also come and visit into my website at http://www.drugrehabtoday.com/

Unknown said...

Hi there,

I'm going to let you in on a few insider secrets that determine the value of a coin laundromat business. These few tips can dramatically increase the your wealth and income.See more at- North York coin laundromats
Thanks and welcome

Anica said...

Hello there! it was a very grateful post, hope that i can have seen new more of your post. Please update me when i back soon. Thank you

Chalis said...

Hi there! Thank you for such a very good information telling more about drug addiction. It's really got a lot of informative info. Thank you for helping with your article. You may also can check and visit into my working website at http://opiaterehab.com/

Zando said...

Hello there! I was very glad that iv'e read your article. It's really good to know more about like your story issues cause iv'e been searching a lots for website today and iv'e love to find-out more for my working website. Thank you for sharing your article, its really big help for me.

Unknown said...

A coin laundromat business is valued based on a multiple of the net income. If you can find a way to increase the income and/or reduce expenses, the value of the store goes up. So, what are some ways you can increase the income? See more at- 24 hour Toronto coin laundromat services

Unknown said...

Furnace is a very important device. In winter it keep normal our home temperature. If this device not work properly you should repair it as soon as possible. Best furnace repair anchorage

Elizabeth J. Neal said...

Positive site, where did u come up with the information on this posting? I'm pleased I discovered it though, ill be checking back soon to find out what additional posts you include. Alexander Mirza CEO

Leesah said...

Great tips! Renting hashing power online is a great way to start mining cryptocurrencies without having to make the investment in mining equipment.

NiceHash allows you to buy hashing power for Bitcoin, Ethereum, Monero, Dash, Zcash, Litecoin and other coins and get paid in bitcoin.

There's no contracts so if mining doesn't turn a profit for you, you can immediately stop your investment.

NiceHash has real miners who use their own mining equipment which is connected to the NiceHash multipool so you'll never have to worry if the mining equipment actually exists.

So if you want to start cryptocurrency mining but you've been hesitant because of shady cloud mining services, this is the solution that you've been looking for.

Click the link below to join NiceHash and start earning bitcoin now:

http://clickmeterlink.com/nicehash

Anna Schafer said...

Wonderful blog! I found it while surfing around on Yahoo News. Do you have any suggestions on how to get listed in Yahoo News? I’ve been trying for a while but I never seem to get there! Appreciate it. bitcoin mixer

Unknown said...

Excellent informative blog.
Laundromate (StarWhites) Vijayawada is a leading laundry service company. We offer excellent clothing, pressing and cleaning services to both household and corporate clients respectively. Laundry with us is a time saving, convenient and affordable undertaking.
Dry Cleaning Add Life to your Clothes. Dry Clean Them Often.
We wash, dry and iron your clothes. Save your time and energy. We deliver on-time.
Free Pickup & Delivery
Enormous Experience in Laundry Services - since 1983
Laundry Services Vijayawada

calvinewers said...

Thanks for sharing the information about Bitcoin, now a days most of the people are investing there money in Bitcoin. To know more about bitcoin visit look at this website here

Flack Jhonsan said...
This comment has been removed by the author.
Flack Jhonsan said...

I wanted to thank you for this excellent read!! I definitely loved every little bit of it. I have you bookmarked your site to check out the new stuff you post. https://bitcoinmix.org

Anonymous said...

It has been a great one You have discussed amazing points about Business. It will be very useful for the readers. I will keep on reading the latest information. Now you can Start Earning Online Money

Danielangelena said...

Whatever the case, keeping your digital assets private makes a great deal of sense. Wait around for transaction to be confirmed and you're all set. If everyone can track your transaction, they can receive your real-life identity. If you are curious to know more about payment network, check here.

Anonymous said...

But do you accidentally hold bitcoins in this https://bitcoinofficial.org wallet?

unknown said...

i was looking at a number of your posts in this website and i conceive this net web site is in imply of fact advisory! hold setting taking vicinity.. antminer s17 tutorial

bill.wood said...

A document that you provide to a third-party should clearly disclose any appropriate risks to a third party funding source. Your attorney can assist you with this matter. Ren Carlton

WilliamsDamion said...

This article will give a brief overview of the Bitcoin Revolution. This is a new Internet money movement that seems to be getting more mainstream media attention. For more ideal details about bitcoin trader scam, visit this website.

Eliza Beth said...

You’ve got some interesting points in this article. I would have never considered any of these if I didn’t come across this. Thanks!. news today

shane lee said...

Indian stocks will get robotically attracted towards putting in money too. Easier said than done! Most investors realize only after putting in their money that there are lots of intricacies involved. stock trading online

albina N muro said...

I'm glad to see the great detail here!. buy real instagram likes famoid

Best said...

Latin American outsourcing can experience growth as call centers, development and design firms cryptocurrence processing

Jessica world smith said...

If you are interested in learning how to make money with your computer and have a computer that has access to the Internet then you should consider downloading a program that will allow you to make money with your computer. To get more detailed info on bitcoin online, visit on hyperlinked site.

Mahmut said...

Bitcoin hesabı açmak mı istiyorsunuz? Tıklayın:Bitcoin hesabı aç

Anonymous said...

Quite an amazing blog post, I literally enjoyed the reading and it made me think about the previous content. Check: Laundry in Dwarka

Dales Air Conditioning said...

Dales Air Conditioning and Heating is the best HVAC company in North Port, Florida. If your air conditioning or heating system is in need of a repair then feel free to give the team at Dale's a call for a free estimate.

Anonymous said...



Nice article about bitcoin thanks for sharing. I also like https://bitcoinmixerguide.com/

WilliamsDamion said...

The bitcoin revolution is critical to know who you are doing business with when you are using a forex currency trading system or any other form system for that matter.

Harry jack said...

Cash available and flowing is absolutely the bread and butter of any small and developing commercial enterprise.Business Capital Loans

casinositeking 카지노사이트 said...

I am always searching online for articles that can help me. There is obviously a lot to know about this. I think you made some good points in Features also. Keep working, great job ! Feel free to visit my website; 카지노사이트

bacarasite said...

Your article has proven useful to me. It’s very informative and you are obviously very knowledgeable in this area. You have opened my eyes to varying views on this topic with interesting and solid content. Feel free to visit my website; 카지노사이트

Madhur Matka said...

Useful information. Fortunate me I found your website accidentally, and I’m stunned
why this twist of fate did not took place in advance.
I bookmarked it.
cheq out my website Satta King Fast
I do not know if it’s just me or if perhaps everyone else experiencing issues with your site.
It appears as if some of the text in your content are
running off the screen. Can someone else please provide feedback
and let me know if this is happening to them too? This might be a problem with my web browser because
I’ve had this happen before. thanks.
Our Site Black Satta King 786 And Charminar Satta King
Satta Matka | Madhur Matka

sumreenanum said...

I still wonder how a system unit like this one would look like if if has an installation of a rotary table.coin-operated washing machine

sumreenanum said...

A system unit like this one doesn't have to have a 5th-axis rotary table. But I still wonder what a system unit like this would look like if it had an installation of a rotary table.coin-operated washing machine

satta matka said...

I am glad to be a visitor to this entire blog! Thanks, for this rare information!. Click Here For Best kalyan chart Game.
kalyan chart

rasmika said...

dsds

Anonymous said...

카지노사이트
온라인카지노
슬롯사이트
우리카지노